Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Fence Installation: The Woodland Hills Owner’s Guide
CGI fence installation in Woodland Hills typically runs $3,500 to $9,000 for a standard residential perimeter, and we carry CGI-compatible parts on our trucks so most jobs get done in a day or two once materials are confirmed. If your CGI fence panel cracked, pulled loose from a post, or the gate has started sagging against the hinges, you don’t have to live with it or rip the whole run out. Most Woodland Hills owners discover the problem the same way: a wind gust off the Santa Monica Mountains finds the weak spot, or a gate that used to swing clean starts dragging across the concrete. The good news is CGI’s modular design means you’re usually looking at a section replacement, not a full teardown.
Before we get deeper into this, one straight fact: Sawyer Remodel Woodland Hills is an independent service provider. We’re not affiliated with CGI, but we’ve installed and repaired their fence systems across the West Valley for years, and we know the product line inside and out. If you’ve got the part number off the original packaging or the engraving on the panel, bring it to the phone call and we can usually match it on the spot.
Which CGI Models This Applies To
CGI fence systems vary more than people expect, and grabbing the wrong panel profile is the most common mistake we see from homeowners who try to source parts themselves. CGI’s residential fence lines include their solid privacy panels, semi-private slats, and decorative aluminum styles, each with different rail spacing and post dimensions. You can’t mix a Commercial series panel with a residential post and expect it to seat properly – the channel widths don’t match.
Here’s what to look for on your existing fence: the post caps and panel edges usually carry an embossed or printed product code. If it’s faded out, measure the panel thickness and the gap between the horizontal rails. Write both down. When you call us, those two numbers plus the fence height get us to the right part fast. On the OEM versus aftermarket question: genuine CGI parts preserve the warranty on the rest of your system and match your existing color without repainting. Quality aftermarket equivalents are usually 20 to 30 percent cheaper and fine for older fences where the finish has already weathered, but we’ll tell you honestly whether it’s worth the savings in your specific case. That decision should never be made without seeing the fence.
Styles & brands we work with
Signs Your CGI Fence Installation Is Failing
- Panels bowing between posts in the afternoon heat. CGI panels expand and contract with temperature swings, and Woodland Hills summers push 100 degrees. If the panels were installed without proper expansion clearance, they’ll cup and eventually crack at the mounting points.
- Gate dragging or binding on one side. This is almost never the gate itself. The post has shifted out of plumb – usually from soil movement in our clay-heavy ground – and the hinges are carrying weight they were never designed to hold.
- Loose or rattling panels after Santa Ana wind events. Wind gusts through the canyons hit fence lines hard. Loose panels mean the self-tapping screws have stripped their bite, and continuing to tighten them just widens the holes.
- Chalky residue on the surface or fading around panel edges. That’s the powder coating breaking down, and once it starts, moisture gets to the aluminum underneath. You’ll see pitting within a year unless the affected sections get replaced or re-coated.
- Gaps opening at the post/panel joint. If the brackets have corroded or the post has moved, the clean seam CGI fences are known for becomes a visible gap. That gap is also where wind gets leverage to start tearing panels loose.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a CGI fence installation in Woodland Hills, you’re looking at $3,500 to $9,000 depending on linear footage, fence height, and whether we’re replacing sections or running new line. A partial repair – say two or three damaged panels plus a reset gate post – usually lands in the $1,200 to $3,000 range. Full replacement of a standard 60 to 100 foot backyard fence with new posts, panels, and hardware sits near the top of the range because you’re paying for materials plus the labor to set posts in our clay-heavy soil correctly.
Every estimate we write is a fixed price. You’ll see parts, labor, dump fees, and any concrete work as separate lines before you approve anything. The number on the invoice is the number you approved – no change orders because we “found something” once the work started. Our workmanship is covered by the 365-Day Done Right Promise: if something’s not right within a year of the install, we come back and make it right, in writing, no argument.
DIY or Call Us?
You can safely check a few things yourself: photograph the panel codes, measure the fence height, and push gently on each post to see which ones have play. That’s the information we need either way. What you shouldn’t do is start pulling panels off a failing fence. Once you remove one panel, the adjacent sections lose structural support, and a gust during the gap becomes a domino chain of bent aluminum. We’ve replaced whole runs that started as a one-panel weekend project.
The honest split: if the fence is cosmetic-only damage on one panel and you already own matching replacement hardware, a careful DIY swap is doable. If a post has moved, a gate doesn’t latch, or more than two panels show damage, the problem is structural and it will keep spreading until the underlying issue gets fixed. Call (341) 217-2776 and we’ll tell you over the phone whether you’re looking at a simple panel swap or something deeper. The estimate is free either way.
FAQs
A properly installed CGI aluminum fence lasts 25 to 30 years in Woodland Hills – maybe longer inland, but our sun exposure and occasional salt air from the coast put real stress on the powder coating. The weak points are always posts in un-draining soil and gate hardware, so expect to replace hinges and reset posts before the panels themselves fail.
Yes, when the damage is isolated to a single panel or a single post, a section repair is usually the right move and runs well under a full replacement cost. If multiple posts have shifted or more than a third of the panels show coating failure, replacement of the affected run costs less than chasing individual fixes for the next three years. Call (341) 217-2776 and we’ll give you an honest read.
A standard repair or panel swap is a one-day job once the parts are confirmed. Full replacement of a 100-foot run takes two to three days, including post setting and concrete cure time before the panels go on. We give you the schedule up front and keep it.
We keep common CGI residential components on the truck – panel styles, brackets, post caps, hinge sets – so most repairs don’t wait on shipping. Custom colors or Commercial series pieces usually take three to five business days to come in. Send us your panel code and we’ll confirm what we have before we even book the visit.
If you’re done guessing which part you need and ready for a straight answer, call (341) 217-2776. We’ll identify what you have, quote the fix in writing, and get your fence back to what it should be. Live person on the phone, 24/7, no callbacks.
Written by Luca Romano, Owner, Sawyer Remodel Woodland Hills at Sawyer Remodel Woodland Hills, serving Woodland Hills and nearby areas.
