Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tremron Roofing: The Woodland Hills Owner’s Guide
If you’re holding a cracked Tremron roof tile or staring at a section that’s slipped out of place, here’s the short version: we stock Tremron-compatible roofing and install replacements in Woodland Hills for $600 – $2,500 on a typical tile repair job, and $8,000 – $20,000 for a full roof replacement. Most Tremron repairs take one visit. You’ll usually spot the problem after a Santa Ana wind event or a heavy winter rain, when a tile ends up in the yard, a ridge cap loosens, or you see water staining on the ceiling below a valley. Tremron concrete tiles are tough, but the underlayment beneath them ages, and the fasteners holding the tiles in place do not last forever. The good news is a failed section doesn’t usually mean a failed roof.
Sawyer Remodel Woodland Hills is an independent contractor. We’re not affiliated with Tremron, but we work with their tile profiles daily across Woodland Hills, Calabasas, and the West Valley.
Which Tremron Models This Applies To
Tremron produces several concrete roof tile profiles, and the part you need depends on which profile your home was built with. The three we see most often in Woodland Hills are the flat shake tile, the rounded barrel tile (sometimes called mission or Spanish profile), and the low-profile slate-look tile. Each profile has its own interlocking edge, so a barrel tile will not seat properly on a flat shake batten system, and vice versa.
To identify yours, check the underside of a loose tile. Tremron stamps the profile name and often a batch date into the concrete. If the stamp is worn, measure the tile’s exposed width. Flat shake profiles typically run 12 to 14 inches wide with a 7 to 8 inch exposure. Barrel tiles are narrower, usually 9 to 11 inches, with a pronounced curve. Slate-look profiles sit flatter and wider, around 14 to 16 inches. If you’re deciding between OEM Tremron tiles and aftermarket equivalents, the OEM route matches your existing color and weathering better – concrete tiles fade in the California sun, and a brand-new tile next to a 15-year-old field will show. Aftermarket tiles from manufacturers like Eagle or Boral can work structurally, but the color match is rarely exact. For roofs under 10 years old, we recommend OEM. For older roofs where a full reroof is on the horizon anyway, aftermarket often makes more financial sense. Luca Romano has matched enough Tremron profiles across the hills above Topanga Canyon Boulevard to know the difference a millimeter of interlock makes, and we check every tile against the existing field before we nail anything down.
Styles & brands we work with
Signs Your Tremron Roofing Is Failing
- Cracked or broken tiles after a wind event. Santa Ana winds regularly hit 40 to 60 mph through the passes into Woodland Hills. Tiles that were nailed once and never re-secured lift, slam down, and crack. One or two broken tiles is normal wear. A dozen suggests a fastener failure pattern.
- Water staining on the ceiling or upper walls. Tile roofs rarely leak from the tile itself. The leak usually traces back to worn underlayment, a split valley flashing, or a lifted ridge cap. In Woodland Hills, the wet season concentrates leaks between December and March.
- Granules or concrete dust in the gutters. Tremron tiles shed small amounts of surface material as they age. Heavy accumulation in the gutter means the tiles are spalling, which accelerates water absorption and freeze-thaw cracking in the rare cold snap.
- Visible gaps at the ridge or hip lines. Ridge caps are the first piece to fail on a concrete tile roof. They sit at the highest point, take the full brunt of wind uplift, and their mortar bedding breaks down over time. A loose ridge cap is a wide-open water entry point.
- Tiles that slide or sound hollow when tapped. A correctly seated Tremron tile is tight against its neighbor. If tiles shift underfoot or rattle in the wind, the fasteners – usually copper or stainless roofing nails – have backed out or corroded through. This is a repair you want before the next big blow.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a Woodland Hills Tremron tile repair, budget $600 to $2,500 on most jobs. A single tile replacement with a color-matched OEM piece runs on the lower end. A repair that involves re-bedding ridge caps, replacing a valley flashing, and re-securing a 10-foot section of field tile pushes toward the top of that range. A full Tremron roof replacement in Woodland Hills lands between $8,000 and $20,000, depending on roof square footage, pitch, and the condition of the existing underlayment.
Every estimate from Sawyer Remodel Woodland Hills includes a written line-item price before any work starts. You’ll see the exact tile cost, the labor hours, the disposal fee for broken tile, and the warranty terms. Our 365-Day Done Right Promise applies to every Tremron repair we install – if the tile we set fails within a year, we come back and fix it at no charge. That’s in writing, on every job.
DIY or Call Us?
You can safely do two things yourself: identify the failed section from the ground with binoculars, and check your attic for daylight or water staining under suspect areas. That’s genuinely useful intel for any roofer you call. What you should not do is walk a tile roof without a proper roof harness and tile-footed walkboards. Concrete tiles crack under concentrated weight, and a 6/12 pitch in Woodland Hills is not forgiving. We’ve repaired more DIY tile damage than storm damage some seasons.
The honest split: inspections from the ground are safe. Repairs at height are not. If you’ve got cracked Tremron tiles, call (341) 217-2776 and we’ll bring the right tile, the right underlayment, and the right harness. The estimate is free.
FAQs
Tremron concrete tiles typically last 40 to 50 years in Southern California, but the underlayment beneath them lasts 20 to 30 years depending on exposure and installation quality. The tiles themselves may be fine while the paper layer underneath has degraded. If your Woodland Hills home is past year 25 and showing leaks, we inspect the underlayment first, not the tile. Call (341) 217-2776 for a free attic and roof inspection.
Small hairline cracks can sometimes be sealed with a concrete tile adhesive, but in most cases a full replacement tile is cheaper and more durable than trying to patch it. A patch fails faster in Woodland Hills sun exposure than a new tile does. We’ll always quote you the replacement option first, because it’s the repair that actually lasts.
A typical single-visit Tremron repair takes 2 to 4 hours. Larger jobs involving ridge cap replacement or valley flashing work may take a full day. If we’re replacing the full roof, expect 3 to 5 days depending on weather. You’ll get a live arrival time and photo updates before and after the work, per The Relay Visibility Guarantee.
We stock the most common Tremron profiles and colors used across Woodland Hills – including the flat shake and mission barrel profiles – on our trucks. Less common colors or older batch profiles may take 3 to 5 days to source from Tremron’s Southern California distributors. We’ll tell you at the estimate which one applies to your roof. For an exact match quote, call (341) 217-2776.
Luca and the crew work roofs from Warner Center to the streets above Ventura Boulevard every week. The work tells you everything. We just make sure it tells the right story. If your Tremron roof needs attention, call (341) 217-2776 for a free estimate. You’ll get a written price, a live arrival time, and a roofer who actually answers the phone.
Written by Luca Romano, Owner, Sawyer Remodel Woodland Hills at Sawyer Remodel Woodland Hills, serving Woodland Hills and nearby areas.
